Pages

Friday, January 18, 2013

Green & Green Settee Part XI

Time to glue up the sides.  Here I'm preparing the tenons for wedges.


Now, I like to drill a small hole at the base of the saw kerf.  Not sure if it works, but it does seem to reduce the risk of splitting.


Glue-up...


Next glue the arms on and then drill a hole into the back of the post to secure the arm with a #12 wood screw.



The screw hole will later be covered by a cleat upon which the upholstery back will rest.  While I have the glue out, I'll glue the cleats onto the side rails (upon which the seat will rest).


Now I need to smooth the front and back transitions where the arms meet the front legs.  I left the arm slightly thick in both the front and back for this purpose.  For the back transition, I tried a couple techniques with the Blacker House arm chair - shoulder plane, carving gouge, small scraper, etc.  I found that a straight chisel works best followed by a file and sand paper.  Works very well.



Now its time for the ebony splines.  I use a bandsaw to cut the profile and rough cut the thickness.  Then I use a small Jet 10-20 drum sander for final thickness (a wonderful machine, I must say).

 
IF I WERE SMART, I WOULD CALL IT A GO AND GLUE UP NOW!  Well, in an attempt to be clever I rough cut the splines thinking that this would save work later.  Wow, was this a mistake!!!


After gluing up the first spline (which went just fine), the second spline decided to split - which went all the way into the groove.  Here I'm frantically trying to glue the split back together, swearing in the meantime.  I believe those swear words are still dangling in space somewhere above my fluorescent lights.


Of course this did not work.  I tried to perform a local repair, but to no avail.  I had to quit and then take another full day off from the shop after this incident.  I then decided to take a few more days off to visit my grandparents.  Time is the best healer.

A few days later, I went into the shop calm but resigned to the fact that I would have to 1)  chop the entire groove to remove the old ebony, 2) expand the groove to renew the edge, 3) and then do the same on the other spline on the other arm so they would be consistent.  This would have to be done by hand as now, with the sides glued up, I could not use the router table.  On the Blacker House arm chair I cut the groove by hand to begin with, so I knew that this is a very feasible task.  Furthermore, at this point I definitely trust my hand tools over using the router hand held to re-cut the groove.


However, on a whim, I decided to see if I could chop out that top spline without mucking up the side walls.  I didn't think this would be possible.  The glue bond would prevent this.  However, with patience this worked!   I use a 3/16" chisel to chop away the ebony center.  With some testing, I was able to find a spot or two on both sides where the ebony chipped away from the side wall just enough to act as a reference edge upon which I could rest my chisel.  With a reference edge, I was able to carefully (and slowly) pare away the remaining ebony from the side walls.  I think the ebony, being very brittle (which caused the split in the first place), allowed me to do this.  For most other woods this probably would not work.


Now, there is still some yellow glue residue in the groove.  I'm a member of the Siskiyou Woodcraft Guild.  We have some very fine furniture makers in the guild with a lot more experience than myself.  I talked to one and he said that as long as I rough up the surface of the side walls the yellow glue will stick to itself.  Since this is a non-stressed joint I'm totally find with this answer.  So, I use a small file and carefully file the side walls, beginning just below the top and only pushing down.  I do not want to damage the top!

Below is another ebony spline fitted and glued into the groove.  Notice that I left copious amount of wood this time!

 

All in all, this mistake set me back almost a week.  However, the project is once more moving forward and not backwards.   I use a coping saw to cut away most of the extra wood.  Then I use a dremel with a course sanding drum to level the spline.  This works very well and fast. 


How proud should the ebony be above the surface?  Obviously, it should be the thickness of a "CharlieCard"...


When I went to North Bennet Street School a couple years ago we used the CharlieCard frequently as a thickness gauge.  I still have a couple.  The CharlieCard is the MBTA train ticket.  Who needs stinkin' rulers anyway!

I'll spare you the dreadful details of sanding, only so say that I take it up to 320 and round it over so it feels good to the hand.  Later I'll swipe it with 600 and then buff it out for a nice shine.


Friday, January 11, 2013

Green & Green Settee Part X

The arms of the Blacker House chair have a wonderful serpentine shape.  The arms for this settee copies that shape. 

My plywood template is too long to fit on the bottom of the arm so I trace out the shape on some heavy paper and truncate the front so it would fit.  Now, due to the inevitable vagaries of the construction process, the paper template is a tad too wide.  Much of that can be attributed to the bloating effect of pencil lines (or should that be "affect" - I get dreadfully confused with "effect" vs "affect").  No problem.  Trace one side so the front/back connects properly, then move the template a bit and trace the other side so the front/back on that side connects properly.  Nice thing about shaping is that there is some wiggle room and aesthetics rather than the necessity of a tight joint is the main determinant.



 

In the photo above note that one side is left uncut so it can be a reference edge on the bandsaw.  First task is to level the sides at the front.  I'm careful to avoid removing any wood at the bottom since it is perfectly mated with the leg.  I use a hand plane and plane across the grain.  Actually, I later switched to a large shoulder plane which worked better.



Using another paper template snippet, I trace out the front side profile and take it to the bandsaw followed by a sanding drum on my drill press.  While I am a fan of the rasp/file technique, using the rasp to smooth out the bandsaw marks in the photo below is a rather difficult procedure since the risk of blowing out the grain on either side is extremely high.  However, it can be done, as that is the way I handled the Blacker House arm chair.


I'm using 60 grit on the sanding drum.  It still took a long time.  One of these days I plan on getting an oscillating spindle sander which I think would work a lot faster with less chance of burning.  I only go up to 80 grit then call it quits as I'm worried about burning.   I use a file to clean up the sanding marks.  (Note that there is a risk of prematurely damaging the file since sanding grit can get stuck in the wood and do some damage to any edge tools.)


With the front shaped, I now shape the sides of the arm.  After taking it to the bandsaw I use a template and a shaper cutter.  Nice thing about the shaper cutter is that I can easily flip the cutter and reverse the direction of rotation to handle grain direction without modifying the template setup.  On a router table one would have to flip the workpiece and template and then switch from a top to a bottom bearing flush cutter (or vise versa).  However, given the shape of the front of the arm this would not be possible unless one had a very narrow router table or unless one flush cuts by hand.  At this point I would rather grab the rasp, file, and spokeshave rather than mess with a router table.


It is tough to get a perfect transition between the front that was shaped earlier with a handplane and the rear that is shaped on the shaper.  I use a spokeshave to smooth out this transition.  Also note that, as with the paper template, I had to adjust the template a bit when switching from one side to the other.


After sanding with 120 and 150 grit here are the arms.


Now is the time to cut the front spline groove.  On the Blacker House arm chair I chopped and pared that by hand, but here I will use the router table.  (Chopping and paring by hand is actually not that difficult and goes fairly fast.)  I have a narrow cutter so I need to make a couple passes to get the desired width (about 5/16"). 




Note that, given the shape of the arm, I was not able to cut all the way to my line.  I still had to chop/pare that part by hand.


Good time to take a break!

Wednesday, January 9, 2013

Green & Green Settee Part IX

There is nothing more to report on Mr. Pumpkin, as my wife turned the compost heap and Mr. Pumpkin is now pushing up daisies.  Oh well.

The arms for the settee are very much like the Blacker House arm chair.  I pretty much followed the same procedure for the settee.  Although there is an older post on how I did the arms for the Blacker House chair, I'll go ahead and repeat the process here, with the risk of being repetitive.  But hey, this is the internet where loquacity is cheap!

The wood for the arms came from the same 8/4 board as the front legs.  The arms have a step in the front.  In order to create this step I cut a "stub" from the front.  This stub will slide directly under to preserve grain continuity, as such (note that I have 2 templates for the arm - a plan view and a side view):

The arm slopes downward towards the rear post.  I need to determine that slope from the drawing, then transfer the angle to the stub.  Now,  it is important to taper the bottom of the stub so the grain flows down inline with the top of the arm.  In the Blacker House chair I did not do this and had to re-cut the stubs as the grain flow did not match and looked pretty bad.


 

Next I cut the taper on the table saw:




Note that after cutting the taper the front of the stub tilts back, as you see in the photo above.  On the Blacker House arm chair this did not sink in.  I cut the mortise in the stub and did not leave enough room up front.  The front tilted too far back and there was not enough wood for the front of the stub to be inline with the front leg.  I had to redo the darn stub a second time!  Fortunately, I had a lot of wood for the arms at the time to cut a second (and final) stub.  If doing an operation for the first time it helps to be liberal with your rough milling.

Here is the stub with the front trimmed and the mortise cut.  I'm using a floating tenon here, so I used the multi-router to cut a mortise in the bottom of the stub and the top of the arm.


Now it's time for the main part of the arm.  The arm narrows as it approaches the back.  I cut this taper on the bottom of the arm with a bandsaw and use a hand plane and shoulder plane to flatten it out:

 
The strategy for the arm is this.  Divide and conquer.  The arm has 3 joints.  I will cut the 2 most difficult joints individually, namely, the front mortise and the rear notch.  The third joint, where the top of the stub meets the bottom of the main part of the arm, is a simple surface joint and I will do this last to complete the joinery.  I've already cut and fitted the mortise in the stub where the arm connects to the front leg.  Now it is time to cut the rear notch where the arm connects to the rear post.  I use my template to locate the rear notch:


 



One thing to note - a subtle but very important detail regarding using a marking knife.  Even though I am using a fine marking knife to mark the location of the notch on the rear leg, in the photo above we see that the knife's bevel is facing up and away from the joint.  The joint will end up being too loose.  Believe me, this will happen!  The correct way to mark this joint is to clamp a small block above and below the arm, remove the arm, then knife the location of the notch.  The knife's bevel will then be facing inward toward the joint and not outward away.  The joint will be tight.  This makes a difference!!! 

Now, why did I not do this?  Because the arm has a taper.  While the joint will be too loose at first, as I slide the arm into the notch the thickness of the arm increases so that the joinery becomes nice and tight.  But, in general, do not forget that the knife's bevel should be facing towards the joint and not away!

Now that the 2 difficult joints are done, we complete the third joint.  At this point, it is a simple task of gluing the main part of the arm to the stub:



The arm is done!  Well, not quite.  We still need to perform the shaping.  Since this post is getting pretty long, I'll do that in another post.

Saturday, January 5, 2013

Green & Green Settee Part VIII

This will be a short post.  It's raining outside and I don't feel like taking a photo of the pumpkin.  But rest assured, in the next post we will see the state of the pumpkin in its post mortem journey.

In this post I need to add a center rail to the seat.  The front of the seat is about 54" long.  This is a lot of span so the upholsterer recommended a center rail.

I cut mortises in both the front and back rails.  I do not want a long tenon that penetrates perpendicular to the length of the front/back rails.  I'm afraid this would weaken the rails too much.  Consequently, I am using double mortises/tenons in line with the length of the rails.  Below I have cut the mortises using the multi-router and a 3/8" bit:


By the way, in case you've noticed, the rear rail in the photo (which is actually the front rail) has some secondary wood glued on.  I believe it is ash.  When I cut the rabbet in the front rail the front rail warped along its length almost an 1/8".  Too much wood was removed for such a long piece.  (Needless to say, I was somewhat pissed).  Consequently, I milled some ash 3/4" thick and glued both together on a flat surface.  This straightened out the front rail nicely.  The front rail is now pretty thick, but it is also darn strong!   Cutting a rabbet 1" x 1/2" is a problematic procedure given the potential of wood movement.  Perhaps next time I will not cut any rabbets and simply glue on a secondary wood to give me the rabbet I need to avoid such wood movement mishaps.

I was going to use floating tenons.  However, I decided against this as the center rail is only an 1" thick and attempting to fit a floating tenon would be problematic.  So I am cutting integral tenons.

First I use a scrap to fit the bottom tenon.  My strategy is to carefully fit the top of the lower tenon to the mortise, then use the multi-router's 3/8" template for final setup to cut the full tenon.  If it is a bit heavy I can easily pare the bottom of the tenon (which is outside) with a shoulder plane.  I cannot pare the top of the lower tenon with a shoulder plane as there is wood above:


In the photo above we see a scrap piece.  The bottom of the tenon has been rough cut so it easily slides into the mortise.  My goal is to exactly fit the top of the tenon.  After a couple tries I get the top to fit nicely.  The multi-router has a plethora of stops.  As I get close I can move a stop by using a piece of paper and moving the stop the thickness of a piece of paper.  In the photo below we see the top of the lower tenon sliding nicely into the mortise.


Now that the upper stop has been set on the multi-router I set the lower stop by using a 3/8" template.  I do not actually use the template during routing.  I use it to simply set the lower stop.  Then I cut the lower tenons on both ends of the center rail:


Now I do the same for the upper tenon.  I use another scrap of wood to fit the bottom of the top tenon exactly, then use the 3/8" template for final setup and route the entire top tenon.  As it turns out, both were a bit thick.  However, I knew that the inside faces of both tenons fit the mortises exactly.  No need to pare there (and doing so would be difficult to say the least).  I only had to pare the outside faces of each tenon a bit for a final fit.  Worked out nicely.  I also squared the mortises:



Then I trim the top of the center rail to be inline with the rabbets.  Here's the center rail finished:



Thursday, January 3, 2013

Green & Green Settee Part VII



In the post mortem photo above we see the pumpkin remains adorned with cherry shavings from when I hand planed the various parts of the settee to remove the machine marks.  Hand planing away the machine marks before glue-up makes sanding much easier later.  Wind and rain has scattered the cherry shavings around a bit.

The settee has a center stretcher.  The settee will be used in an entry way so I wanted to make sure that folks could slide their shoes underneath.   Initially I had the center stretcher centered underneath.  However, I brought it towards the front a bit to add more support to the front section.  I used the golden rule to place the center stretcher towards the front.

The center stretcher is a through mortise/tenon which will be plugged with a dowel from the bottom through the tenon to help secure it.  On top there will be a decorative ebony plug.  I cut the tenon first then the mortise.

I clamp the stretcher to the side stretchers to scribe the top shoulder line.  I use an angle gauge to transfer the angle to my multi-router to cut the tenon.  I use a 3/8" template to cut the tenon.





With the tenon cut I then re-clamp to the side stretcher to mark out the mortise locations.  I only have top and bottom shoulders on the tenon which simplifies the fitting.  Given the knife marks on the bottom of the side stretchers I use the knife to mark out the mortise end locations.  Later I will not worry about those knife marks on the bottom of the side stretchers.  I think it is pretty cool to find furniture maker marks on a piece of furniture, especially on really old pieces.


Unfortunately, I forgot to photograph the mortise process.  In a nutshell, I use my multi-router to cut the mortise through the side stretcher.  The center stretcher is contacting the side stretchers at an angle.  Although I can get pretty close to the angle I need on the multi-router, it is pretty difficult to get dead on for a nice tight fit given the angle.  Consequently, I cut the mortise using a 3/8" bit so the thickness is dead on but I leave the sides heavy and later chisel to the scribe lines for a tight fit on the mortise ends.  I need to square the ends anyway so this is not an extra step

After fitting the tenons, I then pre-drill a "starter" hole in the bottom of the side stretcher on my drill press.  After glue-up I'll finish drilling by hand all the way through the tenon and hammer in a dowel.  More importantly, I pre-cut a square hole on top for the decorative ebony plug.   After glue-up I will not have enough room to negotiate a chisel and hammer to cut the square hole, so now is the time to do this task.